Radial Stamping and Bending Machines
Radially arranged bending slides on a central plate. Up to 11 slides for maximum tooling flexibility. Built in Wehr for three generations.
Machines in comparison
Close this window and use "+ Compare machine" in the portfolio to add more machines.
Advantages of Radial Stamping and Bending Machines
The Biegema quick-change system cuts setup times for the FMS-Q RS by up to 80%. Standardized mounts, defined stops. One shift is enough to reach productive operation.
-
01
Standardized Tool Mounts
Tools are mechanically and electrically pre-configured. No adjustments. No fine-tuning.
-
02
Repeatability of ±0.01 mm
The zero-point clamping system positions tools identically with every changeover.
-
03
Up to 80% Less Setup Time
Turn two hours of setup into just 25 minutes. More throughput per shift.
-
04
Compatible with All FMS-Q RS Models
One tooling set, five machines: 80, 120, 250, 350, and 700 RS. An investment that lasts for generations.
A Direct Comparison of Radial Punch-Bend Machines
Seven key specifications for all five models, directly from the product data.
| Technical data | FMS-Q 80 RS | FMS-Q 120 RS | FMS-Q 250 RS | FMS-Q 350 RS | FMS-Q 700 RS |
|---|---|---|---|---|---|
| Max. strip width | 50 mm | 50 mm | 60 mm | 60 mm | 60 mm |
| Max. strip thickness | 1.5 mm | 1.5 mm | 2.5 mm | 3 mm | 3 mm |
| Max. wire diameter | 4 mm | 4 mm | 6 mm | 8 mm | 8 mm |
| Production output | 400 T/min | 500 T/min | 400 T/min | 250 T/min | 180 T/min |
| Punching force | 80 kN | 80 kN | 250 kN | 350 kN | 700 kN |
| Bending force | 12/22 kN | 12/22 kN | 30/50 kN | 40/60 kN | 40/60 kN |
| Drive power | 4 kW | 4 kW | 15 kW | 22 kW | 22/50 kW |
FMS-Q 80 RS
- Max. strip width
- 50 mm
- Max. strip thickness
- 1.5 mm
- Max. wire diameter
- 4 mm
- Production output
- 400 T/min
- Punching force
- 80 kN
- Bending force
- 12/22 kN
- Drive power
- 4 kW
FMS-Q 120 RS
- Max. strip width
- 50 mm
- Max. strip thickness
- 1.5 mm
- Max. wire diameter
- 4 mm
- Production output
- 500 T/min
- Punching force
- 80 kN
- Bending force
- 12/22 kN
- Drive power
- 4 kW
FMS-Q 250 RS
- Max. strip width
- 60 mm
- Max. strip thickness
- 2.5 mm
- Max. wire diameter
- 6 mm
- Production output
- 400 T/min
- Punching force
- 250 kN
- Bending force
- 30/50 kN
- Drive power
- 15 kW
FMS-Q 350 RS
- Max. strip width
- 60 mm
- Max. strip thickness
- 3 mm
- Max. wire diameter
- 8 mm
- Production output
- 250 T/min
- Punching force
- 350 kN
- Bending force
- 40/60 kN
- Drive power
- 22 kW
FMS-Q 700 RS
- Max. strip width
- 60 mm
- Max. strip thickness
- 3 mm
- Max. wire diameter
- 8 mm
- Production output
- 180 T/min
- Punching force
- 700 kN
- Bending force
- 40/60 kN
- Drive power
- 22/50 kW
The FMS-Q-RS Series. The first choice for springs, contacts, and clips.
Radially arranged bending slides on a central plate, with up to 11 slides for maximum tool flexibility. The FMS-Q-RS series is the classic choice for stamped and bent parts: springs, contacts, clips, and brackets. All produced from a single coil of material in a single machine pass. We build exactly what you need.
Five models, from the compact 80 RS for small production runs to the heavy-duty 700 RS for materials up to 4 mm thick. Now in its third generation.
Which machine suits your part?
Upload a photo, describe your project or select an example. Our system suggests the right solution, and we will call you back today so you receive individual advice.
- 1 Upload a photo, select an example or describe your project.
- 2 You receive an initial machine recommendation and feasibility assessment.
- 3 Start a no-obligation inquiry and talk directly to the engineer.
Analyzing your project — typically 3-5 seconds …
Note: The AI provides non-binding suggestions and initial guidance. Information may contain errors and does not replace personal consultation. For an individual recommendation, please arrange a consultation.
Personal consultation is the way forward here
Send inquiry
Your selection is already saved. Just add your contact details — we will get back to you within 1-2 working days.
All manufacturing examples
Frequently Asked Questions about the Radial FMS-Q RS Series
For complex geometries with multiple bending directions in limited space. Typical applications include contact springs, clips, and retaining clips. Radial machines offer up to 11 slides in a compact footprint.
6 to 11 servo-driven bending slides, depending on the model. The FMS-Q 250 RS has 11, making it ideal for moderately complex components.
Yes. Up to 8 mm wire diameter on the 700 RS. The 80 RS is suitable for thinner spring wire.
Radial: slides arranged in a circle, allowing many tools in a compact space. Linear: slides arranged in a row, ideal for long components such as busbars.
Which radial machine is right for you? We'll help you find the right solution.
- ADDRESS Finsterbachstr. 13 , 79664 Wehr , Deutschland
- PHONE +49 (0) 77 62 / 52 12-50
- EMAIL info@biegema.de
- OPEN Mon – Fri · 8 am – 5 pm